24W US EU UK Plug Medical Grade 12V 2A Wall Mount IEC 60601 Brest Pump Adapter LXCP26
INPUT CHARACTERISTICS
INPUT VOLTAGE & FREQUENCY
Minimum |
Nominal |
Maximum |
|
Input Voltage |
90Vac |
100-240Vac |
264Vac |
Input Frequency |
47Hz |
50Hz/60Hz |
63Hz |
INPUT CURRENT
The maximum input current is 0.8A at nominal AC input voltage and full load.
INRUSH CURRENT
The inrush current will not exceed 50A at 264Vac input for a cold start at 25℃.
STATIC LOSS
The static loss is less than 0.5W at normal input voltage.
The efficiency shall be higher than 70% while measuring at 115VAC&230VAC input voltage, full load.
OUTPUT CHARACTERISTICS
Item |
Model number |
OUTPUT CHARACTERISTICS |
|||
LXCP26series |
Rated output voltage(V) |
Output voltage range(V) |
Rated output current(A) |
Rated output power(W) |
|
Model number |
LXCP26-050 |
5.0 |
4.40~5.60 |
3.00 |
15.0 |
LXCP26-060 |
6.0 |
5.40~6.60 |
2.50 |
15.0 |
|
LXCP26-075 |
7.5 |
7.00~8.10 |
2.66 |
20.0 |
|
LXCP26-090 |
9.0 |
8.50~9.70 |
2.22 |
20.0 |
|
LXCP26-120 |
12.0 |
11.30~12.70 |
2.00 |
24.0 |
|
LXCP26-126 |
12.6 |
11.90~13.30 |
1.90 |
24.0 |
|
LXCP26-135 |
13.5 |
12.80~14.20 |
1.77 |
24.0 |
|
LXCP26-150 |
15.0 |
14.30~15.70 |
1.60 |
24.0 |
|
LXCP26-168 |
16.8 |
16.10~17.50 |
1.43 |
24.0 |
|
LXCP26-180 |
18.0 |
17.30~18.70 |
1.35 |
24.3 |
|
LXCP26-190 |
19.0 |
18.30~19.70 |
1.26 |
24.0 |
|
LXCP26-200 |
20.0 |
19.30~20.70 |
1.20 |
24.0 |
|
LXCP26-240 |
24.0 |
23.30~24.70 |
1.00 |
24.0 |
|
LXCP26-260 |
26.0 |
25.30~26.70 |
0.92 |
24.0 |
|
LXCP26-280 |
28.0 |
27.30~28.70 |
0.85 |
24.0 |
|
LXCP26-300 |
30.0 |
29.30~30.70 |
0.80 |
24.0 |
|
LXCP26-320 |
32.0 |
31.30~32.70 |
0.80 |
25.6 |
|
load regulation |
±5% |
||||
voltage regulation |
±3% |
||||
Overshoot |
≤5% |
||||
Hold up time |
≥10 mS |
||||
Efficiency |
≥70% |
||||
Over current protection(A) |
110-150%Iout |
||||
Ripple and noise |
≤200mV (measured by 20MHz bandwidth oscilloscope and terminated each output with a 0.1uF ceramic capacitor and a10uF aluminum electrolytic capacitor) |
||||
Over temperature protection |
The power supply shall go into stop mode when the IC's temperature is over its trigger point .When IC temperature is lower than regulation value the power supply shall be self-recovering. |
||||
Short circuit protection |
The power supply shall withstand continuous current of short circuit on output no any damage. When the fault condition is removed the power supply shall be self-recovering. |
||||
ENVIRONMENTAL REQUIREMENTS
OPERATING CONDITION
The power supply shall be compliant with each item in this specification for the following environmental conditions.
Ambient Temperature |
-10℃~40℃ |
Relative Humidity |
20%~90% |
STORAGE CONDITION
Ambient Temperature |
-20℃~80℃ |
Relative Humidity |
10%~90% |
Protection Function
MTBF
The power supply is required to have a minimum predicted MTBF (MIL-STD-217F) of 100,000 hours under normal operating conditions and typical usage.
WEIGHT
The weight of the power supply shall be about 120g.
SAFETY STANDARD
The power supply is designed for indoor use and is compliant with IEC 60601-1 and EN 60601-1 standards, as well as other relevant safety regulations.
Electromagnetic Compatiblity
Number |
Item |
Specifications |
Class |
Standards |
1 |
CE |
CLASS B |
/ |
IEC/EN60601-1-2 YY0505 GB4824 EN55011 FCC Part 18 GB4824 |
2 |
RE |
CLASS B |
/ |
IEC/EN60601-1-2 YY0505 GB4824 EN55011 FCC Part 18 |
3 |
SURGE |
Line to line±1KV |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-5 GB17626.5 |
|
|
Line to GND±2KV |
A |
|
4 |
ESD |
Air discharge±15KV |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-2 GB17626.2 |
|
|
Contact discharge±8KV |
A |
|
5 |
EFT/B |
±2KV (BURST FREQUENCY=100KHz) |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-4 GB17626.4 |
6 |
DIP |
Dropped to 0%Ut，last 5000ms(250cycle) |
B |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-11 GB17626.11 |
|
|
Dropped to 30%Ut，last 500ms(25 cycle) |
B |
|
|
|
Dropped to 0%Ut，last 20ms(1 cycle) |
B |
|
|
|
Dropped to 0%Ut，last 10ms(0.5 cycle) |
A |
|
7 |
RS |
Test frequency：80MHz～2700MHz； Field intensity：10V/m； Amplitude modulation：80%AM(1KHz) |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-3 GB17626.3 |
8 |
CS |
Test frequency：0.15MHz～80MHz； Field intensity：6V； Amplitude modulation：80%AM(1KHz) |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-6 GB17626.6 |
9 |
THD |
CLASS A (in system) |
/ |
IEC/EN60601-1-2 YY0505 IEC/EN61000-3-2 GB17625.1 |
10 |
Voltage Fluctuation and Flicker |
Pst≤1.0;Plt≤0.65;Relative steady-state voltage variation dc under3.3%;Maximum relative voltage variation (dmax) under4% |
/ |
IEC/EN60601-1-2 YY0505 IEC/EN61000-3-3 GB17625.2 |
11 |
Power Frequency Magnetic Field |
30A/m |
A |
IEC/EN60601-1-2 YY0505 IEC/EN61000-4-8 GB17626.8 |
Safety: accord with
ITEM |
COUNTRY |
STANDARD |
|
□ |
UL |
USA |
UL60950-1/UL60601-1 |
■ |
CE |
EUROPE |
EN60950-1/EN60601-1 |
■ |
CB |
WORLDWIDE |
IEC 60601-1 |
□ |
TUV |
GERMANY |
IEC60601-1 |
■ |
NRTL |
CUSA |
IEC60601-1/UL60601-1 |
□ |
GS |
GERMANY |
EN60601-1 |
□ |
BS |
ENGLAND |
EN60601-1 |
□ |
SAA |
AUSTRALIA |
AS/NZS6-1 |
Mechanical Requirement
DC PLUG FIGURE(Detail information selection from file of LXC_Dcline_Library.xls)
Label
about us
Our company introduced MES system in 2018, and built 2 fully automated production lines in 2019, which greatly improved product quality, production efficiency and capacity; At present, our factory covers an area of more than 8000 square meters, and our employees more than 300 people; It has 4 automatic placement machines, 4 dispensing machines, 4 automatic solder paste machines, 4 reflow soldering machines, 4 automatic AOI machines, 1 first piece detector, 2 automatic AI insertion machines, 4 wave soldering machines, 8 automatic production lines, 3 automatic radium carving machines, 15 ATE test systems, 10 automatic aging cabinets. In order to achieve comprehensive control, Dragon Star is equipped with various control systems such as WMS, SMT error prevention, ESOP, abnormal call, MES, ERP, etc., so that all stages of production are in the control process.